ATS Advanced 7090

Shopping cart is empty.
- View Cart

Panel Connection - Active Panel Interface

Manufacturer UTC
Model ATS
Version Advanced
Panel Firmware Minimum All versions greater and equal to 026.026.0141-0143
Cable required? Ribbon cable (05-5042)
ATS7090 Peripheral
ATS7090 Versions Version less or equal to V1.02 - Needs SPT version less or equal to V2.06
Version greater or equal to V1.03 - Needs SPT version greater or equal to V2.07
Version V1.05 supports UDL on the latest Panel firmware
None
Panel Profile ATS-Adv-MI or ATSADVANCED
Technical Notes When configuring the panel with a laptop, disconnect the ribbon cable between the Panel and WebWay before connecting the Laptop. When finished, you must disconnect the laptop and then reconnect the ribbon cable.
ATS7090 Peripheral MUST be situated on AUX3.

Panel Connection

Cable Connection

Cable Connection

Panel Cable Connection

Panel Cable Connection

Panel Programming

  • When a running panel and in Installer (Engineer) mode
  • Enter ‘Dialler’ menu [9]
  • Enter ‘CS’ menu [1]
  • Enter ‘CS 1’ menu [1]
  • Enter ‘Transm Path’ menu [2]
  • Select Option [‘TDA75XX’]
  • Enter ‘Protocol’ menu [3]
  • Select option [‘(X)SIA’]
  • Enter ‘Accounts’ menu
  • Select ‘Area n’ with [account numbers]
  • Enter [Mode] menu
  • Select option ‘Primary [CS]
  • Enter ‘Protocol opt’ menu [8]
  • Enter [(X)SIA] menu
  • Set ‘Area Modifier' to [ON]
  • Set ‘Name Chars’ to [30]
  • Set ‘Event Number’ to [3 digits]
  • Set ‘Subev codeing [to ‘Decimal]
  • Set [SIA Frequency] to [Bell]
  • Go back to [Dialler] menu level
  • Enter ‘Path Options’ menu [3]
  • Enter ‘PSTN’ menu [1]
  • Enter ‘Line Fault’ menu and select option [No]
  • Go back to ‘Path Options’ menu level.
  • Enter ‘IP’ menu [4] If present
  • Enter ‘Line Fault’ menu and select option [No]
  • Go back to 'Path options' menu level
  • Enter 'TDA75XX' menu [7]
  • Enter 'Line Fault' menu and select option 'If used'
  • Go Back to Installer Menu level and select Menu 8: Sys Opt > 7: Panel & AB Opts > 9: Remote Config - YES
  • Exit Installer (Engineer) mode
  • Please Note the below
  • May require full panel and SPT re-power
  • User Code : Menu 8:2:1 - Need Acc [YES]
  • The Area Account in the Alarm Events, This might need to be adjusted in the Panel's Settings in order to have a specific Area Number not a generic Account Number [Example: Area 1 - 0001, Area 2 - 0002, etc.....]

Troubleshooting

  • To enter engineer mode, access must be allowed via a setting in User mode.
  • After defaulting the panel, the panel will ask questions on power up.
  • User Code : Menu 8:2:1 - Need Acc [YES]
  • Eng Code : Menu 8: Sys Opt > 7: Panel & AB Opts > 9: Remote Config - YES

  • The Area Account in the Alarm Events, This might need to be adjusted in the Panel's Settings in order to have a specific Area Number not a generic Account Number [Example: Area 1 - 0001, Area 2 - 0002, etc.....]

  • Important Notice:
    ATS Advanced panels running firmware versions 026.026.143 and 028.028.145 have been found to only allow ATS85xx, Remote Manager and the SPT to gain remote access once after a panel reboot. The previous version 024.024.128 still allows multiple ATS85xx, Remote Manager and SPT remote access to the panel.

  • ATTENTION:
    ATS Advanced panels running firmware versions 026.026.0141-0143 and 028.028.0145 have been found to only allow ATS85xx UDL applications, Remote Manager and the SPT to gain remote access once after a panel reboot. The previous version 024.024.0128 still allows multiple ATS85xx, Remote Manager and SPT remote access to the panel.

Compliance

  • Manufacturing of this product is WEEE Compliant. - Further information is avalible in Document (1059353)

UDL information for this item can be found here: UDL Test

Compliance document

Support

Knowledge Base

Panel Guides

Downloads

FAQs

Twitter Updates
Latest News
Contact Details

  Address: 11 Kingfisher Court, Hambridge Road, Newbury, Berkshire RG14 5SJ

  Email: sales@webwayone.co.uk

  Phone Number: +44 (0)1635 231 500